Hign-concerned Chemical:NoneElectronic:NoItem Weight:0.26kgModel Name:ETC600Brand Name:KINGBOLENOrigin:Mainland ChinaItem Type:Battery TestersKINGBOLEN ECT200 Car Circuit Tester Power Probe 12V 24V Automotive Diagnostic Electric Voltage Integrated Power Scanner KINGBOLEN ECT200 Automotive electrical system activator is suitable for 0V - 80V automotive power circuit diagnosis. This product is compact in design and powerful in function. It has reverse connection and overload protection. The tool probe can be used to test conductivity and positive and negative level detection, activate components and other functions, can quickly detect short circuits and broken wires in vehicle electrical system components,It helps users understand vehicle problems faster and more accurately. It is an efficient and advanced testing tool that can greatly improve users' work efficiency. KINGBOLEN ECT200 Circuit Tester Function 1. Positive and Negative Test When the device is connected to vehicle power, the front LED lights will power on. When the probe contacts the positive circuit, the red LED will light up while the voltage value displayed on screens. If the probe contacts the negative circuit, the green LED will light up while the buzzer sounds (screen voltage shows 0.0v) 2. Component Activation The activation function can be used to activate components, such as the starter fuel pump, solenoid valve, blower, cooling fan, headlights, etc. Connect the ground auxiliary clamp to the negative terminal ofthe testing part, connect the probe contact to the positive terminal ofthe testing part,then press the positive activation button (+), the probe will output the positive voltage while with the voltage value displaed on the screen, the red LED will light up, then the testing part will be activated The probe can output positive and negative voltages. Press the (+) button and the probe will output positive voltage, the Red LED will light up while the voltage value displayed on the screen. Press the button and the probe will output negative voltage. The green LED will light up and the buzzer sounds. The maximum activated output current is 8A. Equipment exceeding 8A will activate the trip protection function and the equipment will trip. 3. Continuity Test By using the probe tip and auxiliary ground wire. Continuity testing can be performed on wires and components that are disconnected from the vehicle's electrical system. lf the continuity test passed, the green LED will lightup. NOTE: Do not press the activation switch during the continuity test. 4. Ground Test Use the probe to make contact with the negative terminal ofthe component and the device green LED will light up when the ground test passed NOTE: Do not press the activation switch during ground detection. 5. Test Trailer Lights and Connectors Connect the device to the battery, clamp the auxiliary ground wire's clip to the trailer ground, connect the probe to the socket of the trailer connector, Then press the ( +) button to test the function and direction of the trailer lights. 6. Jumper Function The black clip and the auxiliary ground wire are directly connected through the device, the red clip is disconnected from the vehicle battery, and the device can be used as a long jumper . Please take care to avoid short circuits and over-loads, the jumper function is not protected by the unit's circuit breaker. 7. Track and Locate Short Circuits In most cases, a short circuit will manifest itself as a tripped fuse or electrical protective device (such as a tripped circuit breaker). Follow these steps to trace and locate a short circuit: Trace the wire harness by removing the blown fuse from the fuse box, touching each fuse contact with a probe, noting the number or color ofthe wire, and following the wire as far as possible. lf you are tracing a brake light short, you must first go through the threshold of the wire, find the color or number of the wire and label it If you are tracing a brake light short, you first have to go through the wires. lf the device shows green LED, that means the wires are shorted, so cut the wires carefully and touch each end ofthe wire with a probe. Follow the wire to the correct location. Repeat this step toward the short circuit until you find the exact location ofthe short circuit. Threshold the wire, find the color or number ofthe wire and mark it. KINGBOLEN ECT200 Circuit Tester is with 16.5cm Cables, it is enough to you test the circuit from From the front to the rear KINGBOLEN ECT200 Circuit Tester Supports 12V Cars and 24V Trucks !!! KINGBOLEN ECT200 Circuit Tester Parameter Display : LED Screen Input Voltage : 8V - 32V Test Voltage : 0V - 80V Working Current : 80mA Activation Current : 0V - 8A KINGBOLEN ECT200 Circuit Tester Packing List