Equipment: For Honda CB250F (with digital trip/odo) 2015 For Honda CB300F 2015-2018 For Honda CB400SF 2008-2017 For Honda CB400X 2013-2016 For Honda CB400F 2013-2015 For Honda CB500F 2013-2018 For Honda CB500X 2013-20 18 For Honda CB600F Hornet 2007-2013 For Honda CB650F 2014-2018 For Honda CB1000R 2008-2018 For Handa CBR1000RR 2004-2018 For Honda CB1100 (non-ABS) 2010-2013 For Honda CB1100 (ABS) 2010-2013 For Honda CB1300 S/F 2003-2015 For Honda CBF600 2008-2012 For Honda CBF1000 2006-2009 For Honda CBF1000 F/FA 2006-2009 For Honda CBR250 2015 For Honda CBR300R 2015-2018 For Honda CBR400R 2013-2015 For Honda CBR500R 2 013-2018 For Honda CBR600F 2011 -2013 For Honda CBR600RR 2003-2006 For Honda CBR650F 2014-2018 For Honda CMX300 Rebel 2017 For Honda CMX500 2017 For Honda CRF250L/M all years For Honda Crossrunner all years For Honda CTX700 (w/o DTC) 2014-2017 For Honda Fury 2010-2018 For 2010 Interstate Honda - 2016 For Honda NC400X 2013-2015 For Honda NC700 S/X 2012-2017 For Honda NC750 S/X 2014-2018 For Honda NT700V Deauville 2006-2015 For Honda Saber 2010-2012 For Honda Stateline 2010-2017 For Honda VFR800 Interceptor 2005-2013 For Honda VFR800X all years For Honda VT400 (FI model) 2009-2014 For Honda VT750C (FI model) 2007-2017 For Honda VT750S (FI model) 2007-2009 For Honda VT1300 (all ) 2010-2016 For Honda VTX1800 2005-2012 For Honda XL125V Varadero 2007-2014 For Honda XL700V Transalp (non-ABS) 2008-2014 For Honda XL700V Transalp (ABS) 2008-2014 For Honda XL1000V Varadero 2003-201 2 For Honda TRX ATVs (FI model) all years For Honda CB300R 2018-2019 For Honda GL1800 2005-2017 For Honda CTX1300 2014-2015 For Honda ST1300 2008-2015 For Honda VTR250 2009-2014 (If you encounter any questions, please contact me first, please do not leave negative comments first, hope to answer your questions, thank you) For Honda CB500X VFR 800 CB1000R CB400SF CBR650F CB600F Motorcycle 1-6 ECU Level Plug Transmission Gear oacute;w view Description: Condition: 100% Brand New Color source oacute; for light: Red/blue/green Item name: gear box indicator display Size: 4cm * 4cm * 4cm / 1.57 inch * 1.57 inch * 1.57 inch * 1.57 inch Function: Shows the current number Gear Indicates the current gear from 1st to max. 6th, as well as the neutral indicator. Detects the current gear faster than other gear indicators that use the speedometer/tachometer signal. Display can be mounted anywhere Installation: Locate the red 4-pole male Diagnostic Connector (DLC), usually near the ECU box, may have a removable cap and may be partially covered by black tape. Steps: -You need to configure the module after installation. When the ignition is turned on, it will display backwards (6 to 1), which means the memory is clear. -Raise the rear wheel off the ground with a stand and start the engine in neutral. (If you don't have a stand, you can set up the device while driving. Find a long, straight road with light traffic.) The screen displays L, indicating that learning is started. Slowly accelerate by handle throttle -Display will flash "1". Select first gear, release the clutch and keep the engine speed above idle. The display flashes faster while the device learns the hardware. -When display shows "2", select two-position. Repeat this process until all runs have been thought of (5 or 6). The unit is programmed and should indicate the gears correctly. Now when the ignition is turned on it will flash forward (1 to 6) to indicate it is fully functional. (If there is an error in the learning process, please reset the gear display oacute;w, thank you) Reset: If some gears are not indicated correctly, please reset the gear display oacute;w. Turn on the switch lock key switch. When the oacute;w display shows 5.4.3, immediately turn off the switch lock key switch, and then immediately turn on the switch lock key switch. According to the above operation, turn the key switch lock switch on and off five times in a row to check whether the reset has been completed. Thank you