For HONDA CB600F CBR600F Hornet CBR929RR XL1000V XL125V CBF600 Motorcycle Accessories Gear Indicator Counter Speed Display Meter Please note! This product requires professional installation. It is recommended to find a professional to install it. If you have any problems with the installation, please come to the chat session to find customer service, thank you. Description: Product Product material: LED and ABS Plastic Color: blue, green, orange, red and white Quantity: one piece Easy to install, including installation instructions. Fit: For HONDA CB400 (2001 - 2005) For HONDA CB400SF (1999 - 2005) For HONDA CB600F (2003 - 2006) For HONDA CB600S (2000 - 2002) For HONDA CB900F Hornet (2002 - 2008) For HONDA CB1100SF (1999 - 2004) For HONDA CB1300SF (1998 - 2002) (If you encounter any questions, please be sure to contact me first, please do not leave negative comments first, I very much hope to answer your questions, thank you) Note : The product will display three modes: A, B, and C. You can switch modes by turning the power on and off. When the power is turned on, it will display 6, 5, 4, 3, 2, 1, A, L. The gear indicator can be directly on the Program in this mode, and you can program and use it correctly in this mode. If you need to switch modes, please turn off the power after L is displayed, and then turn the power back on to enter the next mode state. -Product installation and setting methods. -You need to setup the module after installation. When ignition is turned on, the display counts backwards (6 to 1) indicating that the memory is clear. -Raise the rear wheel off the ground by using a stand, and start the engine in Neutral. (If you do not have a stand, you may setup the unit while riding. Find a long, straight road with light traffic.) -the screen displays L, indicating that learning is started. - The screen displays L, select first gear, release the clutch, and keep the speed higher than the idle speed. - The display will flash ;1;;. Continue to maintain the first gear, accelerate. When the device is learning a gear, the display flashes faster. - When the display shows n, relax the handlebar accelerator.When the gear indicator changes from ;n; to ;2;, the motorcycle immediately shifts into ;2; gear, then continue to to refuel and accelerate slowly. - When the display shows n again, relax the handlebar accelerator again.When the gear indicator changes from ;n; to ;3;,the motorcycle immediately shifts into ;3; gear, then continue to refuel and accelerate slowly. Repeat this process until all gears are thought. In the highest gear, when learning sixth gear, the display will flash 6, accelerate until o is displayed, and then 6 will stay on and stop flashing. Indicates that the configuration is complete. The unit is programmed and should indicate the gears correctly. Now, when ignition is turned on, the display counts forward (1 to 6) indicating that it is fully functional. Note: If your motorcycle model and year are within the above applicable model range, and it has 5th gear, you can directly refer to the above configuration method to perform the previous configuration until the gear indicator displays 6, and you do not have 6th gear. Can enter. You directly stay in 5th gear, and then continue to accelerate until the number 6 on the gear indicator is constantly lit, and that's it. If you have any questions, you can contact store customer service. Rest: If some gears are not indicated correctly, reset the unit and set it up again.If you change your gearing (install new front or rear sprocket),or you install a speedometer (or other speedometer calibrator),probably you will have to reset it and set it up again. Cut off the power of the unit 6 times in a row,while the display is counting up and shows3 ,4 or 5. You can power on/off the display by turning the ignition key on/off.On the next power up,the display will count backwards(6 to 1). The memory is clear now and you can perform the Setup procedure. Package List: 1 x Motorcycle Gear Indicator/Bracket(as shown in the picture)