Features: _x005F_x000D_ PTFE lining can bear high temperature and high pressure, corrosion resistance, almost insoluble in all solvents, physical inert. _x005F_x000D_ Hydrothermal synthesis reactor, it is widely used in new materials, energy, environmental engineering and other fields of scientific research and experiments, is the university teaching, research institutions commonly used small reactor. _x005F_x000D_ Hydro-thermal synthesis reactor is a closed vessel, capable of decomposing insoluble substances. _x005F_x000D_ It can be used for sample dissolution pre-treatment in analysis like atomic absorption spectroscopy and plasma emission. _x005F_x000D_ Also, it can be used for synthesis of small doses. Achieving the purpose of rapid digestion of insoluble substances by taking advantage of strong acid/alkali, high temperature and pressure confined environment available. _x005F_x000D_ It's helpful in dissolving samples in the determination of trace elements. _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ Specification: _x005F_x000D_ Condition:100% Brand New_x005F_x000D_ Item Type: Hydrothermal Autoclave Reactor_x005F_x000D_ Material: 304 Stainless Steel + PTFE Liner_x005F_x000D_ Color: As shown in the picture_x005F_x000D_ Maximum Pressure: 3Mpa_x005F_x000D_ Security Pressure: 2Mpa_x005F_x000D_ Maximum Temperature: 200 _x005F_x000D_ Security Temperature: 180 _x005F_x000D_ Heating, Cooling Rate: 5 / min_x005F_x000D_ Use: External heating_x005F_x000D_ Capacity: 25ml_x005F_x000D_ _x005F_x000D_ What is PTFE?_x005F_x000D_ Poly tetra fluoroethylene,polymer compound made from tetrafluoroethylene, which has excellent chemical stability and corrosion resistance, is one of the best materials for corrosion resistance in the world._x005F_x000D_ No poison - Physical inert_x005F_x000D_ Non adhesion - the smallest surface tension in solid materials_x005F_x000D_ High lubrication - the lowest coefficient of friction in solid materials_x005F_x000D_ High temperature and low temperature resistance - the working temperature can reach 250 degrees centigrade, even if the temperature drops to -196 C, it can maintain 5% elongation_x005F_x000D_ Corrosion resistance - almost insoluble in all solvents_x005F_x000D_ Thickening kettle bottom: high security, high pressure resistance and prevent cracking_x005F_x000D_ Strong sealing: prevent leakage circular groove seal safe use_x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ Operation Method:_x005F_x000D_ 1. Place the synthetic reactor in the heater and raise the temperature to the required temperature ( less than the prescribed safe temperature )_x005F_x000D_ 2. At the end of the reaction, the cooling rate should be 5c/min strictly in order to avoid damaging the reactor._x005F_x000D_ 3. After confirming the temperature in the kettle is lower than the boiling point of the solvent in the reactant, loosen the cover of the kettle, and then open the cover of the kettle._x005F_x000D_ 4. Pour the reactant into the PTFE liner and ensure that the feeding is less than 80%, and for the first time must less than 30%_x005F_x000D_ 5. Install the kettle body correctly and tighten the kettle cover.The hydrothermal synthesis reactor is placed on a heater and heated to the desired reaction temperature (less than the required safe temperature) at the rate specified._x005F_x000D_ 6. When the reaction is complete, it should be cooled, and the cooling rate should be strictly followed to ensure safety and the service life of the reactor._x005F_x000D_ 7. When confirming that the temperature in the abdominal cavity is below the boiling point, the solvent reaction system can only open the lid after subsequent operations._x005F_x000D_ 8. The hydrothermal synthesis reactor should be cleaned after each use to avoid corrosion. The sealing line of the kettle body and lid should be kept clean to prevent any turbulence._x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ Package List: _x005F_x000D_ 1 x Hydrothermal Autoclave Reactor(5 parts) _x005F_x000D_ 1 x Boost Rod _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ Note: _x005F_x000D_ Suggested Heater: It is recommended use a heater with programmed heating, muffle furnace is not recommended, because of temperature overshooting and temperature heating rate exceed the limit will lead to melting of the lining.